[cobalt-security] Server and log wierdness

[Scott Genevish <genevish@xxxxxxx>]

This morning I discovered my RaQ3i was not working.  A few minutes after 
I noticed this, it started up again.  In trying to investigate the 
problem, I noticed some seemingly odd entries in my /var/log/messages 
file.  Is any of this something to be worried about?  (I snipped some of 
the entries that seemed fine.)

Apr 12 16:06:12 training init: Switching to runlevel: 1
Apr 12 16:06:15 training sshd[327]: Received signal 15; terminating.
Apr 12 16:06:19 training kernel: Kernel logging (proc) stopped.
Apr 12 16:06:19 training kernel: Kernel log daemon terminating.
Apr 12 16:06:21 training exiting on signal 15
Apr 13 10:50:39 training syslogd 1.3-3: restart.
Apr 13 10:50:42 training kernel: klogd 1.3-3, log source = /proc/kmsg 
started.
...
Apr 13 10:50:42 training kernel: eth0: Invalid EEPROM checksum 0x4f9f, 
check settings before activating this device!
Apr 13 10:50:42 training kernel: eth0: Intel EtherExpress Pro 10/100 at 
0x1100, 00:10:E0:01:BF:3D, IRQ 11.
Apr 13 10:50:42 training kernel:   Board assembly 000000-000, Physical 
connectors present:
Apr 13 10:50:42 training kernel:   Primary interface chip None PHY #0.
Apr 13 10:50:42 training kernel:   General self-test: passed.
Apr 13 10:50:42 training kernel:   Serial sub-system self-test: passed.
Apr 13 10:50:42 training kernel:   Internal registers self-test: passed.
Apr 13 10:50:42 training kernel:   ROM checksum self-test: passed 
(0xdbd8681d).
Apr 13 10:50:42 training kernel:   Receiver lock-up workaround activated.
...
Apr 13 10:50:50 training kernel: portmap: RPC call returned error 111
Apr 13 10:50:50 training kernel: RPC: task of released request still 
queued!
Apr 13 10:50:50 training kernel: RPC: (task is on xprt_pending)
Apr 13 10:50:55 training kernel: portmap: RPC call returned error 111
Apr 13 10:50:55 training kernel: RPC: task of released request still 
queued!
Apr 13 10:50:55 training kernel: RPC: (task is on xprt_pending)
Apr 13 10:50:55 training kernel: lockd_up: makesock failed, error=-111
Apr 13 10:51:00 training kernel: portmap: RPC call returned error 111
Apr 13 10:51:00 training kernel: RPC: task of released request still 
queued!
Apr 13 10:51:00 training kernel: RPC: (task is on xprt_pending)
Apr 13 10:51:00 training rpc.statd[249]: unable to register (SM_PROG, 
SM_VERS, udp).
Apr 13 10:51:01 training modprobe: can't locate module block-major-22
Apr 13 10:51:01 training modprobe: can't locate module block-major-22
Apr 13 10:51:01 training modprobe: can't locate module block-major-33
Apr 13 10:51:01 training modprobe: can't locate module block-major-33
Apr 13 10:51:01 training modprobe: can't locate module block-major-34
Apr 13 10:51:01 training modprobe: can't locate module block-major-34
Apr 13 10:51:01 training modprobe: can't locate module block-major-8
Apr 13 10:51:01 training last message repeated 4 times
Apr 13 10:51:01 training modprobe: can't locate module block-major-13
Apr 13 10:51:02 training modprobe: can't locate module block-major-13
Apr 13 10:51:02 training sshd[327]: Server listening on 0.0.0.0 port 22.
Apr 13 10:51:02 training sshd[327]: Generating 768 bit RSA key.
Apr 13 10:51:03 training sshd[327]: RSA key generation complete.
Apr 13 10:51:10 training PAM_pwdb[365]: (su) session opened for user 
postgres by (uid=0)
Apr 13 10:51:10 training PAM_pwdb[365]: (su) session closed for user 
postgres


Thanks,

-Scott
--------------------------------
Scott Genevish
Training Systems Project Manager
Kinko's, Inc
(805) 477-5307
--------------------------------